Notes and links from around the field

The Ankle Mobility Drill I Use Before Every Squat

Before front squats, back squats, goblet squats or a heavy leg session, I spend a few minutes on one ankle mobility drill. It is simple, needs no equipment and gives me a quick read on whether my squat stance needs adjusting that day.

The drill is a controlled knee-to-wall movement. I keep the heel down, guide the knee towards the wall and use the motion to warm the ankle rather than forcing a stretch. It works well in a home garage, a commercial gym in Sydney or a chilly Melbourne training space.

I started doing it because my squat depth could change from one session to the next. A long drive, a hard AFL-style running session, old shoes or a stiff morning could all make the bottom position feel different. This short check makes the first loaded set more predictable.

Drill option Best use What I watch
Knee-to-wall rocks General warm-up Heel stays grounded
Bent-knee ankle rocks Deeper squat preparation Smooth forward travel
Loaded ankle drive Before heavy sets No pinching or collapse
Calf raise with knee forward Strength through range Controlled tempo

Why I Start At The Ankle

A squat asks the ankle to accept forward movement while the foot stays connected to the floor. If the ankle does not offer enough dorsiflexion, the body often finds another route: the heels lift, the feet turn out sharply, or the torso folds forward.

That does not mean every squat problem comes from limited mobility. Hip control, trunk strength and stance width matter too. The ankle drill is useful because it takes very little time and helps me separate a genuine restriction from a poor setup.

The Knee-To-Wall Setup

I face a wall and place one foot a few centimetres away, usually with the big toe pointing straight ahead. I keep the heel, the base of the big toe and the base of the little toe in contact with the floor. Then I gently drive the knee towards the wall.

If the knee reaches the wall easily, I slide the foot back slightly. If the heel pops up or the foot rolls in, I move closer. The target is not the biggest possible distance. I want a clean, repeatable range that feels similar on both sides.

How I Perform The Drill

I use eight to ten slow repetitions per side, pausing briefly at the furthest comfortable point. The movement stays active: knee forward, heel heavy, foot relaxed, then return under control. I avoid bouncing because a warm-up should prepare the joint, not turn into a test of tolerance.

For a particularly stiff day, I complete two rounds. On a warm Brisbane morning, one round is often enough. In a cold Melbourne garage during winter, I may spend extra time walking around first, since the drill feels better once the whole body is warm.

What The Foot Should Do

The foot is part of the drill, not a passive platform. I try to keep a gentle three-point contact with the ground while allowing the arch to move naturally. Clawing the toes or gripping the floor usually creates more tension than useful stability.

I also watch the knee track in line with the second or third toe. It does not need to travel perfectly straight, but it should not collapse dramatically inward. This small detail carries over well to goblet squats and split squats, especially when training in minimalist shoes or lifting barefoot.

Adjusting For Different Squats

For a high-bar back squat, I pay attention to whether the ankle allows the knees to travel forward without the heels becoming light. For a front squat, the same restriction can make it difficult to keep the chest tall while reaching depth.

A heel-elevated squat can be a sensible variation when the goal is quad work or when ankle range is temporarily limited. It does not replace mobility work, though. I like using a small wedge or weightlifting shoe for the session while still practising the knee-to-wall drill. A useful mobility reference can also sit alongside the practical checks I use in training.

When I Add A Loaded Version

Once the bodyweight reps feel smooth, I sometimes place a small plate under the forefoot and perform slow ankle rocks, or hold a light kettlebell while driving the knee forward. The load should be modest enough that the heel remains planted and the motion stays quiet.

This is especially handy before a heavier strength session at a commercial gym, where I may not have space for a long stretching routine. It also suits Australian training habits: a few minutes before a lunchtime session in Sydney or a weekend park workout can be enough to make the first squat sets feel less abrupt.

The Cue I Keep

I do not chase a particular centimetre measurement. I look for a heel that stays down, a foot that remains grounded and a knee that moves forward without pain or a sharp pinch. Then I repeat the same check after the session or a few days later.

That consistency matters more than forcing extra range. The drill is a quick readiness screen and a way to rehearse the ankle position required by the squat. The main thing to remember is simple: move the knee forward, keep the heel heavy, and let the squat variation match the range you can control.